Empty factory unit with a glossy grey epoxy floor marked with white lane lines and hatched walkways

Epoxy Flooring in Pinetown

Sixteen kilometres inland from the city, Pinetown's industrial parks run on their floors. Forklift aisles, wash-down bays and workshop slabs that have taken years of oil all need something tougher than paint, and the work has to fit around production.

Get a Free Quote

Westmead, New Germany and the rest of the belt

Pinetown is one of four main industrial hubs in the Durban-Pinetown region. On the western side are Westmead, Mahogany Ridge, Alexander Park and Surprise Farm; to the north, New Germany has Falcon Industrial Park, Mountain Ridge, New Germany Industrial Park and Pineside. The businesses based here range from textiles and protective clothing to snack foods, wholesale and chemicals.

That mix means one street can need three different floors: a dry warehouse that only wants dust sealed and aisles marked, a food line that is hosed down every shift, and a chemical store where a spill must not eat into the concrete. Our industrial and commercial coatings page goes through each type.

A rough Pinetown price list for industrial floors

People searching for Pinetown floors often ask for a price list. Here are installed, per-square-metre figures from South African guides published in 2026. Treat them as a starting point, not our quote.

System	Per m², installed	Where the figure comes from
Chemical-resistant epoxy, 3 mm and up	R350 to R1 000	One SA installer's published guide
Industrial 100% solids epoxy system	R800 to R2 000	One SA flooring cost guide
Polyurethane screed, 3 to 4 mm	R350 to R600	Same installer's guide
Heavy-duty polyurethane concrete	R1 200 to R2 500	A Durban cost guide
Add-on: moisture-tolerant primer	+R120 to R250	Same Durban guide

Wide ranges are normal here. Film thickness, the chemicals involved, how much repair the slab needs and whether we can work in one go or must phase around shifts all move the number. Home garages and decorative finishes are on our full epoxy price guide.

How long the floor is out of action

On a warm day of around 30 °C, the technical sheet for one common epoxy body coat lists a minimum of 16 hours before the next coat, about 18 hours before people can walk on it, around two days for light traffic and five days to full cure. At 20 °C each of those stretches out.

We split big floors into bays so one area cures while the next is prepared, and we give you the date for each bay in the quote.

Testing an old workshop slab

Primer data sheets ask for concrete that is clean, dry, free of oil and grease, and strong enough at the surface; one sets a minimum pull-off strength of 1.5 N/mm². In an old workshop, years of drips are the first thing to check.

We grind a test patch, look at how the stains respond and check moisture before we price anything.

Also on our map

If you have a house as well as a plant, our pages on epoxy for Durban North garages and patios and floors in uMhlanga cover the residential side.

Pinetown factory and workshop questions

Nobody can price a factory floor from a list, because thickness, chemicals and the state of the slab change everything. Published South African guides do give ballparks: roughly R350 to R1 000 per square metre for a 3 mm chemical-resistant epoxy, and R800 to R2 000 for an industrial 100% solids system. We give you a fixed written figure after measuring and testing your floor.

A small area often can be, but forklifts are the limit. In warm conditions a typical epoxy coat can be walked on after about 18 hours, yet light traffic waits around two days and full cure takes about five. We would plan to be off the floor by Monday with pedestrian routes open, and agree when trucks can come back.

Where the floor sees hot wash-downs, fats or aggressive cleaners, a polyurethane screed is usually the better choice. Epoxy suits dry storage, assembly lines and workshops. Tell us exactly what lands on the floor and at what temperature, and we will match the system to it.

Coating manufacturers require the slab to be clean and free of oil, grease and old coatings before priming. Some staining grinds out. Deep contamination may need cleaning and testing first, and in bad spots cutting out and patching. We check this at the site visit, because a coating will not hold on oily concrete.

Get a figure for your floor

Send the square metres, what the floor carries and what gets spilled on it. We will arrange a visit, test the slab and come back with a written quote.

Start a quote request